F01 Hisense washer: water inlet fault

Reviewed 2026-11-18 against 3 Hisense manuals. See sources.

Disclosure: this page has spots for parts links. When those links go live, we may earn a commission if you buy through them, at no extra cost to you. It doesn’t change what we recommend.Read the full disclosure.

What F01 means

F01 is Hisense’s “water inlet fault.” The washer didn’t get the water it expected while filling. [1, p. 58]

On models with a water-inflow warning icon, the manual says the icon lights when the faucet isn’t open or the water pressure is too low, and F01 shows at the same time. [1, p. 42]

Safety first

Step-by-step owner checks

  1. Make sure the faucets are fully open

    Check that both supply faucets behind the washer are turned fully on. [1, p. 58; 1, p. 42]

  2. Consider your water pressure

    The WF5S2845BW specifications list a supply pressure range of 15 to 145 psi (100 to 1000 kPa). If the pressure in your home is unusually low, the washer may not fill fast enough. [1, p. 18; 1, p. 58]

  3. Look for pinched or kinked inlet hoses

    Check that the hoses aren’t crushed between the washer and the wall and aren’t stretched or kinked. [1, p. 58; 1, p. 24]

  4. Clean the inlet filters

    With the faucets off, unscrew the inlet hose at the washer, take out the small mesh filter, rinse off any sediment, and put the filter back. Reconnect the hose, then open the faucet and check for leaks. Hisense suggests cleaning these filters at least every six months, and more often if you have hard water. [1, p. 52]

  5. If it’s freezing, thaw the inlet hoses

    Hisense’s method: switch off and unplug the washer, then turn off the faucets. Pour hot water over the frozen faucets and remove the hoses. Soak the hoses in hot water, reconnect them, turn the faucets on, and run a spin-only cycle. [1, p. 53; 1, p. 54]

  6. Resume the cycle

    Once the supply problem is fixed, press Start/Pause to carry on. [1, p. 58]

Model differences:

Parts involved

Water inlet hoses

Bring water from the faucets to the washer. Hisense says to check them for cracks, leaks and wear, replace them every five years, and always use new hoses when you install a washer. [1, p. 24; 1, p. 6]

Owner-replaceable

[PLACEHOLDER affiliate link: “Water inlet hoses” for Hisense washer. No affiliate ID yet]

Inlet filter screens

Sit where the hoses connect and keep particles out of the inlet valve. Clean them. Don’t remove them for good. [1, p. 52]

Owner cleans it; no routine replacement

Hisense’s manual doesn’t name an internal part behind F01. If the faucets, pressure, hoses and filters are all fine and F01 keeps coming back, a technician should diagnose it. Hisense says to use only manufacturer-approved spare parts. [1, p. 59]

When to call a pro

Hisense prints its service phone number on the front of each manual. Have the model and serial number from the nameplate ready when you call.

Common questions

What does F01 mean on a Hisense washer?

F01 is Hisense’s water inlet fault. The washer isn’t filling properly, usually because a faucet is closed, the pressure is low, a hose is pinched or frozen, or an inlet filter is clogged.

What water pressure does a Hisense washer need?

The specifications for the Hisense WF5S2845BW list 15 to 145 psi (100 to 1000 kPa). Check your own model’s specification table.

How often should I clean the inlet filters?

Hisense recommends at least every six months, and more often if your water is hard or you see limescale.

Other Hisense washer codes

Sources

  1. Hisense Canada, User's Operation Manual, WF5S2845BW front-load washer (models: WF5S2845BW (24 in., 3.1 cu. ft., 120 V)). PDF · support page. Accessed 2026-11-18. North American (120 V) manual. Page numbers are the printed page numbers in the English section.
  2. Hisense Malaysia, User's Operation Manual, WF105M3 washer (models: WF105M3, WF105M3*). PDF. Accessed 2026-11-18. Non-US model. Used only to confirm that the code meanings match across Hisense front-load washers.
  3. Hisense New Zealand, User's Operation Manual, HWF5I9014 washer (models: HWF5I9014, HWF5I9014B, HWF5I9014W2/W3, HWF5I9014B2/B3). PDF. Accessed 2026-11-18. Non-US model. Used only to confirm the code meanings and the "Confirm Start" step on newer controls.

Code meanings come from the Hisense WF5S2845BW manual (sold in Canada, 120 V) and match the Hisense WF105M3 and HWF5I9014 manuals. Hisense says some codes only apply to certain models, so check the fault table in your own manual too. Wording on this page is our own summary of those documents. Points without a citation are our general advice on when to stop and get help, not manufacturer statements.